On sliding and/or rolling gates this U-channel is installed on the back side of the gate at least half way up the height of the gate. This U-channel will allow for protruding pickets or arched top gates.

On the telescoping gate system, this galvanized 1-1/4" I.D. U-Channel is used on the 2nd and 3rd gate leaves in conjunction with an upper guide plate to ensure the telescoping gate will be steady at the top.

This channel has a 1-3/8" OD, 1-1/4" ID. It is 1-3/8" tall and 1/16" thick.

Supplied is 9'10" lengths.

One of our customer service representatives will contact you in regards to shipping your item.

In order to ship UPS, bar must be cut to no more than 7'9" feet. There is a $5.00 per cut charge.

On sliding and/or rolling gates this U-channel is installed on the back side of the gate at least half way up the height of the gate. This U-channel will allow for protruding pickets or arched top gates.

On the telescoping gate system, this galvanized 1-1/4" I.D. U-Channel is used on the 2nd and 3rd gate leaves in conjunction with an upper guide plate to ensure the telescoping gate will be steady at the top.

This channel has a 1-3/8" OD, 1-1/4" ID. It is 1-3/8" tall and 1/16" thick.

Supplied is 19'8" lengths.

One of our customer service representatives will contact you in regards to shipping your item.

In order to ship UPS, bar must be cut to no more than 7'9" feet. There is a $5.00 per cut charge.

On sliding and/or rolling gates this U-channel is installed on the back side of the gate at least half way up the height of the gate. This U-channel will allow for protruding pickets or arched top gates.

On the telescoping gate system, this U-Channel is used on the 2nd and 3rd gate leaves in conjunction with an upper guide plate to ensure the telescoping gate will be steady at the top.

Monorail supplied in 9.84FT sections (3000mm)

One of our customer service representatives will contact you in regards to shipping your item.

In order to ship UPS, bar must be cut to no more than 7'9" feet. There is a $5.00 per cut charge.

On sliding and/or rolling gates this U-channel is installed on the back side of the gate at least half way up the height of the gate. This U-channel will allow for protruding pickets or arched top gates.

On the telescoping gate system, this aluminum 1-1/4" I.D. U-Channel is used on the 2nd and 3rd gate leaves in conjunction with an upper guide plate to ensure the telescoping gate will be steady at the top.

Use with guide roller, item 258.30

Supplied is 10' lengths.

One of our customer service representatives will contact you in regards to shipping your item.

In order to ship UPS, bar must be cut to no more than 7'9" feet. There is a $5.00 per cut charge.

On sliding and/or rolling gates this U-channel is installed on the back side of the gate at least half way up the height of the gate. This U-channel will allow for protruding pickets or arched top gates.

On the telescoping gate system, this aluminum 1-1/4" I.D. U-Channel is used on the 2nd and 3rd gate leaves in conjunction with an upper guide plate to ensure the telescoping gate will be steady at the top.

Use with guide roller, item 258.30

Supplied is 20' lengths.

One of our customer service representatives will contact you in regards to shipping your item.

In order to ship UPS, bar must be cut to no more than 7'9" feet. There is a $5.00 per cut charge.

The guide plate is used with the U-channel at the top of the gate for stability.

This roller will work with RG-387 and CG-237 U-channel and is used for the telescoping gate system (Ranger) only

The guide plate is used with the U-channel at the top of the gate.

Comunello recommends this guide for added stability with changing wind speeds and smoother rolling gates.

This roller will work with RG-387 and CG-237 U-channel and is used for the telescoping gate system (Ranger) only