NOTE: Most product dimensions are approximate within manufacturing tolerances and in many cases are a close approximation after converting from metric.

Push-Lock Fittings for 3/16" Cable, for Metal or Wood Posts

Item Number :
Push-Lock Fittings PL-6-XX

The Push-Lock® is a concealed, swageless, non-tensioning, through-the-post-mounted fitting that is suitable for use on level runs only, and is available for 1/8” and 3/16” diameter  
1x19 stainless steel cable.

This fitting is made to look similar to the Invisiware® Receiver from the exterior of the post, so it is recommended to use a Receiver with stud on the opposite end whenever practical to maintain a consistent look.

FOR METAL POSTS
The Push-Lock® fitting must be used with a tensioning fitting on the opposite end of the run. This fitting is installed into a pre-drilled hole in the end post. Using the Push-Lock® fitting requires enough clearance on the back side of the end post (to install the fitting through the back side of the post) and that amount of clearance depends on the length of the Push-Lock® fitting chosen. This fitting is furnished with a Delrin® washer that is installed between the shoulder of the fitting and the end post to protect the surface of the finish of the end post as tension is applied. It is recommended that you choose a length of Push-Lock® that is the same as the cross section dimension of the end post. The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools.



FOR WOOD POSTS
The Push-Lock® must be used with a tensioning fitting on the opposite end of the run. This fitting is installed into a pre-drilled hole in the end post. Using the Push-Lock® fitting on level runs requires that a minimum of 1-1/2” of clearance exists on the back side of the end post (to install the fitting through the back side of the post). It is also recommended that a stainless steel flat washer be installed between the shoulder of the fitting and the mating surface of the wood post (washer sold separately. The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools.

Use Push-Lock® PL-6-12 for wood posts

Use Stainless Steel Washer 7/16SAE on wood posts


Grouped product items

Push-Lock fitting for 3/16" Cable. Can use with 1-1/2" flat sided frame, 1-1/2" round tube frame, 1-1/4" pipe frame or wood posts, swageless option

This Push-Lock® is for 3/16" cable.
Frame option: 1-1/2" flat sided frame, 1-1/2" round or square tube, 1-1/4" Pipe OR wood posts
Length: 1.562"

Item Number : PL-6-12

PRICE :

$19.50

QTY :

Push-Lock fitting for 3/16" Cable. Can use with 2" flat sided frame, 2" round tube frame or 1-1/2" pipe frame, swageless option

This Push-Lock® is for 3/16" cable.
Frame option: 2" flat sided frame, 2" round or square tube OR 1-1/2" Pipe‡
Length: 2.030"

‡will protrude from cable side of post +/- 1.8"

Item Number : PL-6-2.030

PRICE :

$23.50

QTY :

Push-Lock fitting for 3/16" Cable. Can use with 3" flat sided frame, 3" round tube frame, swageless option

This Push-Lock® is for 3/16" cable.
Frame option: 3" flat sided frame or 3" round or square tube
Length: 3.030"

Item Number : PL-6-3.030

PRICE :

$28.50

QTY :

Stainless Steel Washer for 1/8" or 3/16" Cable

This stainless steel washer is used with various Ultra-tec hardware fittings.

Washer O.D. = 59/64"
Washer I.D. = 31/64"

Item Number : 7/16SAE

PRICE :

$0.40

QTY :

More Information

More Information
Item Number Push-Lock Fittings PL-6-XX
Brands Ultra-tec
Cable Size 3/16" Cable
Post Material Metal, Wood
Frame Options 1-1/2" tube-round or square, 2"x2" tube-round or square, 3" tube-round or square